Installing SSL cert for OWA
Sat, 15 Apr 2006 22:21:04 -0300
I have installed a new Exchange 2003 two node cluster which is working fine,
but whenever I try to install an SSL certificate for OWA and choose the
'require SSL' option it fails the HTTP virtual server resource. Are there
any special hoops to jump through when using SSL in a cluster?
I am also struggling ...
|
Exchange Cluster Backup W/ SAN's Storage
Sat, 15 Apr 2006 13:15:01 -0700
Hi,
I just installed an Exchange 2003 two node active / passive server attached
to an EMC shared SAN’s storage device where the mail-store and public folders
reside. I need to make sure the two cluster node server and SAN’s are being
backup properly. I have Veritas 10.0 backup software.
Can someone pl ...
|
Need Help for Exchange DR Plan....
Thu, 13 Apr 2006 22:30:01 -0700
currently we are running 4 node exch cluster with SAN storage and this SAN is
realtime sync with another SAN at DR site. My question is how to setting up a
exchange server (cluster) at DR site and connect to SAN DR.
at the end of the plan, we can bring down production server and up the DR
server or vice v ...
|
Convert E2K3 Active-Active to Active-Active-Passive
Thu, 13 Apr 2006 15:05:15 -0400
Hi there,
We currently have a two node Active-Active Exchange 2003 cluster, and we've
since realized that AA is not the way we want to continue working.
As such, we'd like to add a node to the cluster, so that there is a passive
node (Active-Active-Passive).
I could not find any documentation from Mic ...
|
Stand-by cluster across different subnet
Thu, 13 Apr 2006 01:21:02 -0700
Pls help.
I am planning to install a stand-by lcuster across tow different sites
having different subnets.
Now, it is MS requirement to give the same IP addresses to EVS and its
resource as your primary site. In that case, how can i give the same IP
Address if both my primary cluster setup and stand-by a ...
|
How many RUS (EC/Domainxxx) to be said enough in Single Domain?
Tue, 11 Apr 2006 12:08:40 -0700
Dear All,
I have 3 Domain Controller (also GC), let's call it A, B, C (A is the 1st
DC, 5 roles)
and I have 1 st Exchange server D, 2nd virtual cluster exchange server E.
However I checked in recipient update in ESM, we do only have:
"Recipient Update Service (Enterprise Configuration) - Domain - DC A -
...
|
Remove clustered POP3 resource
Tue, 11 Apr 2006 08:46:02 -0700
I have POP3 enabled as a resource on my clustered Exchange 2003 servers.
We've decided to remove it to enhance our security. Can I just go into
cluster administrator and delete it or is there more involved in getting rid
of it? What are the consequences of doing this? (In other words, do you have
to fail o ...
|
|
|
system attendant and/or smtp virtual server hangs on failover
Tue, 11 Apr 2006 04:08:02 -0700
hello,
we installed a 3-node exchange 2003 cluster i noticed that when i take a
resource offline or when i do a failover most times the system attendant
and/or the smtp virtual server hangs until the cluster takes it offline due
to timeout. i also increased the time these services are allowed to take but ...
|
Active/Active backend server
10 Apr 2006 04:58:11 -0700
Hi all,
I have configured a exchange cluster on backend servers and I want
it to be active/active. So what I did was that added two physical disk
as resource disk and created two virtual servers in two nodes
seperately. Then only i could create two virtual servers. But I only
have one exchange virtual ser ...
|
Exchange Contingency planning
Mon, 10 Apr 2006 02:53:01 -0700
i have a centralized site where all exchanve servers reside including
front-end and back-end.
wht do i need for contingency?
is there any document available from MS?
pls guide.
...
|
